Search Results for : midi


MM-16 MIDI Monitor (DIY kit)

  MM-16 MIDI Monitor DIY kit. MIDI monitor is standalone box for displaying MIDI messages on LEDs, powered from MIDI itself (no power supply or batteries required). All components are included, kit requires soldering (common tools required: soldering iron, tin, cutting pliers, tweezers). Assembly instructions: assembly_rev.0 There are three modes of operation switchable by button: […]


M-221 MIDI to clock synchronizer (8HP)

M-221 MIDI to clock module for Eurorack / Doepfer A100 system. M-221 MIDI clock: – one MIDI input (DIN 5pin) – 8 clock outputs: 1/4, 1/8dotted, 1/8, 1/16dotted, 1/16, 1/32dotted, 1/32 and “fine MIDI clock”= 24 trigs per quarter note – 5 control outputs: start (trig), stop (trig), reset (trig), play (gate – active while […]


M-217 Trig/gate to MIDI w. velocity (8HP)

M-217 Trig/gate to MIDI with variable velocity (manual or voltage controlled) 12 trig/gate input jacks velocity CV jack + minimum velocity knob (see below) setting button MIDI out + LED Covers all possibilities of M-215 and M-216 and adds variable/adjustable velocity. Works in two modes:  “One MIDI channel” (like M-215) – sends notes in halftone […]


M-218 Trig/gate to MIDI w. velocity (8HP)

  M-218 Trig/gate to MIDI converter with velocity recognized from trigger/gate level. Converts trig/gates to MIDI notes (note and channel can be set independetly for all channels), three velocity curves (low/linear/high), mute on/off (supress sending MIDI notes), note-off message sent as note-on/vel=0 or as note-off/vel=half of note-on velocity (jumper selectable), processing time under 2ms in […]


M-330 Clock to MIDI sync (6HP)

  M-330 Clock to MIDI synchronizer Allows sync MIDI devices from Eurorack clock. Clock in jack (24 clock ticks means 1 quarter note in slaved MIDI device) Start, Continue and Stop input jacks Divided clock output jack for driving eurorack modules + button + LED. There are two main modes of operation (selectable by long […]


M-211 MIDI to gate 12ch. converter (8HP)

  12ch MIDI to gate converter interface Ladik M-211 for eurorack / Doepfer A100 system. Simple programming: 1.press learn button, LED lights up. 2. play 12 notes (any notes on any channels) and you are done, LED goes off. Setting and mode are memorized even when switched off. All outputs can be assigned to any […]


M-260 MIDI thru box (6HP)

MIDI thru box, 1in/3out Ladik M-260 for eurorack / Doepfer A100 system. Data LED (blinking if data flows), no need for 5V rack power bus (powered from 12V rail). No data manipulation, optocoupled input of course. Splits one MIDI input to three MIDI ouputs (if you have not “thru” connector on your modules or to […]


M-240 MIDI to trig 4ch velocity converter (6HP)

red arrows shows jumper positions   Velocity sensitive (dynamic!!!) 4ch MIDI to trig converter Ladik M-240 for eurorack / Doepfer A100 system. Variable trigger levels (according to incoming note velocity) MIDI to trig interface (output in 0..5V or 0..10V ranges). Great for drum modules triggering, no need for “accent” input and yet you get incomparable […]


M-210 MIDI to trig 12ch. converter (8HP)

    12ch MIDI to trig converter Ladik M-210 for eurorack / Doepfer A100 system. Works as “12ch” or “11ch+1accent” MIDI to trig interface (accent active if note velocity is 80 or more). Great for drum modules triggering (I think 11 or 12 drums is quite enough) 🙂 Simple programming: 1.press learn button, LED lights […]


U-090 Clock/Reset Corrector (4HP)

  U-090 Clock/Reset Corrector module for Eurorack / Doepfer A100 system From the top down: Wait time knob Reset width knob Clock input jack + LED Reset input jack + LED Setting button + LEDs (short pressing sets gap between reset and clock, holding button sets clock pulse width) Clock output jack + LED Reset […]