S-230 Shuffled grid module for Eurorack / Doepfer A100 system. From the top down left column: clock input + LED reset input + LED setting button + 2 LEDs (short press sets trigger memory, long press sets trigger length) retrig button + LED swing knob + CV input jack output jack + LED right […]

S-411 Shaper module for eurorack / Doepfer A100 system. Compares input voltage (or ctrl input voltage, normalled to input if ctrl jack is not plugged-in) with adjustable thresholds (positive and negative). While input signal (or ctrl input) exceeds positive (or is below than negative) threshold then output is switched to DC level set by level […]

S-620 Composer G (gates) module for Eurorack / Doepfer A100 system. From the top down: CLK: Clock input jack (trigger) + LED ENBL: Enable input jack (gate) + LED PROB: Probability of new note being generated knob + new note generated indicator LED DENS: Gate Density or Odd/Even Beat Probability knob (jumper selectable) S LEN: […]

S-610 Composer N (notes) module for Eurorack / Doepfer A100 system. From the top down: CLK: Clock input jack (trigger) + LED ENBL: Enable input jack (gate) + LED PROB: Probability of new note being generated knob + new note generated indicator LED SPRD: Note Spread knob S LEN: Sequence Length knob + LED QUANT: […]

F-711 SV-VCF (State-Variable / Multimode) voltage controlled filter module for Eurorack / Doepfer A100 system. CV input jack (V/oct) Manual tune knob Resonance knob (selfoscillates dirty at high Q) Audio input jack Filter audio outputs (high-pass, band-pass, low-pass)   Width: 4TE/ 4HP/ 20mm Depth: 50mm /2″ max. Current: 20mA max. Double check power connection before […]

U-012 Dual Attenuverter module for Eurorack/Doepfer A100 system. From top: input jack attenuation/inversion knob DC shift knob output jack + 2 polarity LEDs and same for second channel U-012 allows manipulation with input signal, red knobs sets signal attenuation and/or inversion, white knobs sets DC offset (transposition). Red knob “under” 12 o´clock (ccw) inverts signal, […]

   E-480 Contour generator module for Eurorack/Doepfer A100 system Left column: trig/gate input + LED rate knob + LED first integrator time knob first integrator output jack + polarity LEDs second integrator time knob second integrator ending decay knob second integrator output jack + polarity LEDs Right column: 8 three-position switches (down/stay/up) offset knob E-480 […]

M-217 Trig/gate to MIDI with variable velocity (manual or voltage controlled) 12 trig/gate input jacks velocity CV jack + minimum velocity knob (see below) setting button MIDI out + LED Covers all possibilities of M-215 and M-216 and adds variable/adjustable velocity. Works in two modes:  “One MIDI channel” (like M-215) – sends notes in halftone […]

M-012 Bipolar V-meter module for eurorack / Doepfer A100 system. 3 switchable ranges (front panel switch): -2 to +2V, -4 to +4V, -8 to +8V, zero in the middle. 4 steps for positive and 4 steps for negative voltage in selected range. One normal output (parallel), one output inverted. Very handy for checking CV or […]

  M-011 bipolar V-meter module for eurorack / Doepfer A100 system. 3 switchable ranges (panel switch): -2 to +2V, -4 to +4V, -8 to +8V, zero in the middle. 4 steps for positive and 4 steps for negative voltage in selected range. Very handy for checking CV or audio levels between modules. For example – […]